See what our Experts say about this CURT Trailer Hitch Ball

• Weight Distribution System for 3500 GVWR Pop-Up Camper Towed by Toyota Tundra
  Anytime the fully loaded and ready to tow trailer weight is greater than 50 percent of the weight of the tow vehicle, using weight distribution should be considered. When you get the pop-up, hitch it to the vehicle and pay special attention to the front and rear ride height of the truck. If the rear end sags more than a few inches when the camper's hitched up, your headlights will be aimed incorrectly and braking and steering response can be negatively affected because of the sag at the...
  view full answer...
• Replacement Channel Mount Ball Platform for 20K 3 Inch Wide Adjustable Curt Shank
  The internal channel width of the Replacement Shank for Curt Adjustable 2-Ball Mount # C45917 is 3" while the Replacement Ball Platform # C28KR you're looking at has a 2-3/4" width and is for the Curt Rebellion XD rated only for 15K as opposed to the 20K rating for your shank. Since there will be a 1/4" difference I recommend going with the Curt Pintle Hook # C45922 instead which has the higher rating to match your shank plus it comes with a 2-5/16" hitch ball that can be swapped out for...
  view full answer...
• Can Different Sized Hitch Balls be Used with Curt Pintle Hook # C45908
  Yes, the 2-5/16 inch hitch ball that comes included with the Curt Pintle Hook # C45908 can be swapped out with a different sized ball that features a compatible shank. For a 2 inch hitch ball to use with this assembly the Curt # C48820 will work perfectly. We also have the 1-7/8 inch # C48810 if you think you would ever have a need for a smaller hitch ball. I have attached a short video demonstration on the Pintle Hook that you can also take a look at.
  view full answer...
• Difference Between The Curt 45920 And 45922 Channel Mount Htich Ball
  Along with # C45922 having the ability to tow more than 7,000 lbs more than # C45920, the Curt Pintle Hook with 2-5/16" Hitch Ball # C45922 can also be changed to use a 1-7/8" ball # C48810 and a 2" ball # C48820. The Curt # C45922 also has a built in anti-rattle design that helps reduce towing noise, and can fit lunette ring couplers with a diameter of 2-12" or 3".
  view full answer...
• Is there a 1-7/8 Inch Trailer Hitch Ball with a 1-1/4 Inch Shank
  Ball # C48810 is the only 1-7/8 inch diameter ball that also has a 1-1/4 inch shank. Like you said it is made to fit a pintle hitch combo ball mount. What I recommend is a ball with a 1 inch diameter shank like # 19260 and then use bushing # 58184 or # F-2 to use it in your ball mount with the 1-1/4 inch opening.
  view full answer...
• Availability of Ball Mount With 3" Rise/Drop
  I'm not sure if you're looking for a 3" rise or drop but we have options for both so you don't need to worry about being off by an inch. For a ball mount with a 3" rise you can use the # 40331. You will also need # C48810 for a 1-7/8", # A-90 for a 2", or # 19286 for a 2-5/16" hitch ball. If you need a drop you can use the # TS64FR. This has a 3-1/4" drop but the 1/4" difference won't be noticeable.
  view full answer...
• Could 1-7/8 inch Hitch Ball Fit in Clevis Adapter # BWTS35100B
  The diameter of the hole on the platform of the # BWTS35100B is 1-1/4 inch so a 1-7/8 inch hitch ball like the part # C48810 would fit.
  view full answer...
• Is There a 1-7/8 Inch Hitch Ball with a 5,000 Weight Capacity
  The majority of standard hitch balls with a 1-7/8" diameter will have a 2,000-3,500 lb weight capacity. If you need a hitch ball with a 1-7/8" diameter that has a 5,000 lb weight capacity then you will need to use a pintle hitch ball. For this, we have part # C48810 which has a 1-1/4" diameter shank. You will need to measure the hole for the hitch ball on your ball mount in order to make sure this one will work for you. The only difference between a standard hitch ball and a pintle hitch...
  view full answer...
  
• Mounting Torque For Curt Pintle Hook # C48200
  When it comes to the recommend torque specs for the four bolts on The Curt Pintle Hook with 2-5/16 inch Hitch Ball # C48200 per Curt you will need to tighten all the bolts to 90 ft. lbs. The pintle hook has a bolt-on installation to Pintle Hook Mounting Plate # C48343. The pintle hook has interchangeable hitch hitch balls that will let you easily swap for a 1-7/8 inch hitch ball # C48810 or a 2 inch ball # C48820 (both sold separately). The item has a strong forged steel construction...
  view full answer...
• Complete Towing Setup For 2010 Ford Edge
  Dry weight is the weight of your vehicle when completely empty with no passengers or cargo loaded. The gross trailer weight is total weight of the trailer plus the cargo loaded on it. The main two things you need to look at are your vehicle's max towing capacity and the trailer's gross weight. My research tells me that your 2010 Ford Edge has a max towing capacity of 2,000lbs, but you can verify in your owner's manual. This means you should not pull a trailer that exceeds 2,000lbs. If...
  view full answer...
• Availability of a Trailer Hitch Ball with a 1-1/4 Inch Shank and a 1-7/8 Inch Diameter
  The only 1-7/8 inch ball that we carry with a 1-1/4 inch shank is # C48810, but this is used for a pintle hitch combo hitch. What you can do is use a bushing like # F-2 to go from a 1-1/4 inch ball hole to a 1 inch. You could then use a ball like # 19260.
  view full answer...
• Which Hitch Balls Fit the Curt Pintle Hook Part # C48200
  The Curt Pintle Hook, part # C48200, includes a 2-5/16 inch hitch ball. For other sizes use part # C48820 for a 2 inch or part # C48810. Both have a 1-1/4 inch shank.
  view full answer...
• How to Reduce Trailer Sway While Towing with a 2017 Jeep Wrangler Sport
  In order to help reduce trailer sway while towing with your 2017 Jeep Wrangler Sport, I recommend using a weight distribution system like the Reese Steadi-Flex Weight Distribution System part # 66557. The Steadi-Flex is going to not only help reduce trailer sway but it will also help to distribute tongue weight which improves braking and the overall handling of your tow vehicle. The only thing you will need to use this system is a hitch ball, part # C48810 or part # 63845. Please note...
  view full answer...
  
• 2 Trailer Hitch for a 16-High Boat Trailer on a 2014 Toyota Sienna
  It sounds like you're looking for a 2" hitch and a ball mount that raises a 1-7/8 ball 16" off the ground with a wiring harness. We have a combination that will work well for hooking up your trailer to your 2014 Toyota Sienna. First up: the hitch. We actually have an etrailer hitch designed for the 2014 Sienna. It's the Class III, 2" hitch, part # e98853. It has a maximum tongue weight of 525 pounds and trailer weight of 3500 pounds, so it should be able to carry your boat trailer with...
  view full answer...
• Pintle Hitch Adapter For The Curt Adjustable 2-Ball Mount # C45902
  Hi Andrew, Based on what you're describing it sounds like you have the Curt Adjustable 2-Ball Mount # C45902, which is compatible with the Curt Pintle Hook with 2-5/16" Hitch Ball # C45922. This is also rated for 20,000lbs and the 2-5/16" hitch ball can be swapped out with a 1-7/8" # C48810 or 2" # C48820 hitch ball if needed.
  view full answer...
• Hitch Ball Diameter Compatible With Curt Pintle Hook With 2 Inch Hitch Ball # C48190
  If by the ball hole size of the Curt Pintle Hook with 2inch Hitch Ball # C48190 you mean the compatible diameter of the hitch ball shank, it is 1-1/4 inches. You can change out the hitch ball size as needed as long as you keep this shank diameter so you can use # C48830 for a 2-5/16 inch hitch ball and # C48810 for A 1-7/8 inch option. This is compatible with lunette ring couplers with diameter of 2-1/2 or 3 inches.
  view full answer...
• Does Curt 1-7/8" Hitch Ball for Curt Pintle Hook Work With Standard Ball Mount
  Yes, a standard ball mount is compatible with the Curt 1-7/8" hitch ball you asked about, which is the following part number: - Hitch Ball for Curt Pintle Hook Combo - 1-7/8" Diameter - 6,000 lbs # C48810 The # C48810 has a 2-3/8" long shank which is plenty long enough to mount to a standard ball mount platform and allow you to tighten the nut.
  view full answer...
• Availability of Bolt On Pintle Hook Combo with 1-7/8 Ball
  It sounds like you are looking for something like our Curt Pintle Hook with 1-7/8" Hitch Ball # C48810. As you can see in the attached photo, it comes with a 1-7/8 ball and it allows you to bolt it onto a pintle mount or drawbar, like # C48343, similar to the one you mentioned having. I have also attached a review video for this at the bottom of the page. All of our pintle hook combos come with a pre-torqued ball so you can just keep your other one as a spare. If you were looking for...
  view full answer...
  
• Can 1-7/8" Hitch Ball be Used for the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount
  Yes, since the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount # C45949-22516 uses standard hitch balls you can definitely install a 1-7/8" hitch ball if the need arises to tow a smaller trailer. Just make sure it has a 1-1/4" shank like the Curt Hitch Ball # C48810 does and you're good to go!
  view full answer...
• How to Choose the Correct Ball Mount for a 2017 Kia Sedona
  In order to determine the correct amount of rise/drop you will need in a ball mount you will want to measure from the ground to the bottom of the coupler on your trailer while level then subtract this measurement from the ground to the top of the inside edge on the hitch for your 2017 Kia Sedona. I have attached a help article that will walk you through this process as well. When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75894 on a 2015/2016 Kia Sedona we found...
  view full answer...
• Recommended Ball Mount with 6 Inch Drop That Won't Stick Out Further Than 10 Inches From Receiver
  I can understand the concern with using a ball mount with a drop and a longer shank possibly creating a situation where it's more likely to contact the ground. I'll start by saying that the Curt Multi-Ball # D900 is a fairly standard length when it comes to an adjustable ball mount; there are some that come with a longer shank but the roughly 15" total distance from the center of the hitch pin hole to the center of the hitch ball is fairly standard. Since you're looking to bring the hitch...
  view full answer...
• Length of Shaft on Hitch Ball for Curt Pintle Hook Combo-1-7/8" Diameter - 6,000 lbs - Chrome C44810
  The length of the shaft on the Hitch Ball for Curt Pintle Hook Combo - 1-7/8" Diameter - 6,000 lbs - Chrome is 2-3/8" long from the bottom of the ball platform to the bottom of the shaft.
  view full answer...
  
• Availability Of 2-5/16" Hitch Ball with 1-1/4" Diameter Shank That Is At Least 3" Long
  It sounds like you are looking for a hitch ball with a long shank. We have the exact 2-5/16" hitch ball you are looking for which is the 2-5/16" Hitch Ball w/ 1" Rise - 1-1/4" Diameter x 3-1/4" Long Shank - Raw - 24K # BWHB94003 which has a 1-/4" diameter shank and a 3-1/4" long shank. While we do have a 1-7/8" hitch ball that has a 1-1/4" shank, the # C48810, it only has a shank that is 2-3/8" long. Your best bet would be to purchase a separate ball mount with a 1" diameter ball mount...
  view full answer...
• Pintle Hook with 2" Hitch Ball Combo Needed for B&W Pintle Hook Mounting Plate
  You can use the Curt Pintle Hook with 2" Hitch Ball # C48190 with the B&W Pintle Hook Mounting Plate # BWPMHD14005. When you use the 2" hitch ball your towing weight capacity is 10,000 lbs but then that is increased to 16,000 lbs when using the pintle hook. If you end up needing to use a different sized hitch ball then you can easily swap out to a 1-7/8" ball with part # C48810 or a 2-5/16" ball with part # C48830. Review videos have been linked for you to check out.
  view full answer...

Do you have a question about this Trailer Hitch Ball?